AEG L61271WDBI Manual do Utilizador

LAVAMAT 61271 WDBI EN User manual

• after pressing button 8: it will be im-possible to change any other pro-gramme or option.To enable or disable this option press si-multaneously for

ProgrammeMaximum and Minimum TemperatureType of LaundryMaximum LoadCycle De-scriptionOptionsDelicates40° - 30°Max. load kg 3 - Reduced load kg 2Delica

ProgrammeMaximum and Minimum TemperatureType of LaundryMaximum LoadCycle De-scriptionOptionsCotton Economy60°Max. load 7 kgWhite and fast coloured cot

6.1 Drying programmesTimed programmesDegree of Drying Type of FabricDryingLoadSpinSpeedSugges-teddryingtimeMinutesEXTRA DRYIdeal for towelling mate-ri

7. CONSUMPTION VALUESProgramme Energy con-sumption(KWh)Water con-sumption(litres)Programmeduration(minutes)White Cottons 95° 2.2 72For the du-ration o

Make sure that no laundry stays betweenthe seal and the door. There is a risk ofwater leakage or damage to the laundry.9.2 Filling the detergent and a

If you turn the programme dial toanother programme when theappliance is working, the yellowpilot light of button 8 blinks 3times. The display shows th

9.9 Setting the DELAY START(button 9)Press this button again an again to setthe required delay.The display shows the set delay time val-ue (up to 20 h

The water must be emptied out beforeopening the door. During this time thedrum continues to turn at regular inter-vals until water drain.Follow the be

the drum and select an additional dryingcycle of 20-30 minutes.9.16 NON-STOP programme:Washing and Timed dryingThe recommended load size is 3 kg forco

CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY

• Button up pillowcases, close zippers,hooks and poppers. Tie up belts.• Empty the pockets and unfold theitems.• Turn inside out multilayered fabrics,

• For the maximum laundry load of thedrying programmes, refer to the dry-ing programmes table.Do no not set a drying programme forthis laundry:– Very

11.3 Door sealRegularly examine the seal and removeall objects from the inner part.11.4 DrumRegularly examine the drum to preventlimescale and rust pa

11.6 Drain pumpThe pump should be inspected regularlyand particularly if:• the appliance does not empty and/orspin;• the appliance makes an unusual no

7.Check carefully whether the pumpimpeller rotates (it rotates jerkily). Ifit doesn’t rotate, please contactyour Service Centre.8.Put the cap back on

4.Remove the inlet hose behind theappliance.5.Clean the filter in the valve with astiff brush or a towel.45°20°6.Install again the inlet hose. Makesur

During machine operation it is possiblethat the yellow pilot light of button 8blinks, one of the following alarm codesappears on the display and at th

Problem Possible cause/SolutionThe machine does notempty and/or does notspin:The drain hose is squashed or kinked. • Check the drain hose connection.T

Problem Possible cause/SolutionThe machine vibratesor is noisy:The transit bolts and packing have not been re-moved.• Check the correct installation o

Problem Possible cause/SolutionThe laundry is full ofdifferent colored fluff:The fabrics washed in the previous cycle releasedfluff of a different col

1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i

4.Remove the internal film.5.Open the door. Remove the poly-styrene piece from the door sealand all the items from the drum.6.Put one of the polystyre

9.Remove the power supply cable andthe drain hose from the hose hold-ers.10.Remove the three bolts. Use the keysupplied with the appliance.11.Pull out

13.2 Positioning and levelling• Install the machine on a flat hard floor.• Make sure that air circulation aroundthe machine is not impeded by car-pets

• Connect the water inlet hose to thecold water tap with 3/4 thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extensio

• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a

• Directly to a built-in drain pipe in theroom wall and tighten it with a clip.You can extend the drain hose tomaximum 400 cm. Contact theservice cent

Preparation and assembly of the door• The machine is originally pre-arrangedfor the assembly of a door openingfrom right to left (Fig. 2).Fig. 2Ø 35 m

BA• Mounting the doorFix the hinges to the appliance bymeans of the M5x15 screws . The hing-es can be adjusted to compensate forpossible uneven thickn

38www.aeg.com

ENGLISH 39

• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.

www.aeg.com/shop132927191-A-032012

Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected tothe water mains using the new sup-plied hose-se

• Disconnect the appliance from themains supply.• Cut off the mains cable and discard it.• Remove the door catch to preventchildren and pets to get cl

4. PRODUCT DESCRIPTION7 8 9101 234561Detergent dispenser2Control panel3Door handle4Rating plate5Drain pump6Feet for the appliance level7Water drain ho

5. CONTROL PANEL1 2 3 4 5 6 7 98 10ABC1Programme selector dial2SPIN button•Rinse hold position 3STAIN button4TIME SAVE button5EXTRA RINSE button6DRYIN

Alarm codesIn the event of operating problems, some alarm codes can bedisplayed, for example (see chapter «Troubleshooting»).End of programmeWhen the