AEG L6047FL Manual do Utilizador

L 6047 FL EN User manual

6. PROGRAMMESProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsCottons95° - ColdWhite and colouredcotton with normalsoil.max

ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsDrain All fabricsThe maximum loadof the laundry is rela-ted to the type of

programmes in terms of combined energy and water consumption for washing normallysoiled cotton laundry.Set this programme to have a good washing resul

Off Mode (W) Left On Mode (W)The information given in the charts above are in compliance with the EU Com-mission regulation 1015/2010 implementing dir

9.2 Filling the detergent and additivesThe detergent compartment for the prewash phase, the soakprogramme and for the stain function.Add the detergent

3.To use powder detergent, turn theflap up.4.To use liquid detergent, turn theflap down.With the flap in the positionDOWN:– Do not use gelatinous or t

2.Turn again the programme knob toa new washing programme. At thistime you can also set the availablefunctions.The appliance does not drain thewater.9

2.Press the Start/Pause button 4 .The appliance drain the water andspin.3.When the programme is completedand the door lock symbol goes off,you can ope

• mmol/l (millimol for each litre - inter-national unit for the hardness of wa-ter).• Clarke degrees.Water hardness tableLevel TypeWater hardness°dH °

11.5 DrumRegularly examine the drum to preventlimescale and rust particles.Only use special products to remove rustparticles from the drum.To do this:

CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY

WARNING!1.Disconnect the mains plugfrom the mains socket.2.Do not remove the filterwhile the appliance oper-ates. Do not clean the drainpump if the wa

7.Make sure that the impeller of thepump can turn. If this does not oc-cur, contact the service centre.218.Clean the filter under the water tapand put

4.Remove the inlet hose behind theappliance.5.Clean the filter in the valve with astiff brush or a towel.45°20°6.Install again the inlet hose. Makesur

• - The appliance does not drainthe water.• - The appliance door is open ornot closed correctly.WARNING!Deactivate the appliance beforeyou do the chec

Problem Possible cause Possible solutionThe programmedoes not start.The mains plug is notconnected in the mainssocket.Put in the mains plug. Blow out

After the check, activate the appliance.The programme continues from thepoint of interruption.If the problem occurs again, contact theservice centre.I

5.Open the door and remove all theitems from the drum.6.Put one of the polystyrene packag-ing elements on the floor behindthe appliance. Carefully put

10.Remove the three bolts. Use the keysupplied with the appliance.11.Pull out the plastic spacers.12.Put the plastic caps in the holes.You can find th

13.3 Positioning and levellingx4• Install the appliance on a flat hardfloor.• Make sure that carpets do not stopthe air circulation below the applianc

13.4 The inlet hose20O20O20O45O45O45O• Connect the hose to the appliance.Turn the inlet hose only left or right.Loose the ring nut to set it in the co

1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i

Water-stop deviceAThe inlet hose has a water stop device.This device prevents water leaks in thehose because of its natural ageing. Thered sector in t

• If the end of the drain hose is this (seethe drawing), you can push it directlyinto the stand pipe.Without the plastic hose guide.• To a sink spigot

13.6 In the interest of the environment• Connect the appliance to the FOULsystem for the drain water. The sew-age works keeps the drain water forthe t

ENGLISH 33

34www.aeg.com

ENGLISH 35

www.aeg.com/shop132919231-A-022013

• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.

mains plug, use a 13 amp ASTA (BS1362) fuse.•This appliance complies with theE.E.C. Directives.Water connection• Make sure not to cause damage to thew

Level of protection against ingress of solid particlesand moisture ensured by the protective cover, ex-cept where the low voltage equipment has no pro

4.1 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit

• After 5 minutes from the end of thewashing programme. Refer to 'At theend of programme'.5.2 Programme knob 2Turn this knob to set a progra

5.4 Start/Pause button 4Press button 4 to start or interrupt aprogramme.5.5 Delay start button 5Press button 5 to delay the start of aprogramme from 3